Remote Control Model 12 Led Group, Tamiya RC Car Simulation Linkage, Three-way Controllable Turn Signal Light

Simulated flash twee LED Lighting kit steering brake for 1/10 Scale model remote control vehicle Yokomo Tamiya HSP HPI AXIAL RC4WD TRX Flight model simulation of Tiangong 12-lamp remote control lamp Characteristics of flash lamp: 12 LED lights Simulated lamp Easy to use Distant flash Circuit board design improvement, HOSI power saving Headlights white, blue tail lights, brake lights red, turn yellow Suitable for 1/10 RC vehicles Product specification: Name: 12 LED Lighting System Kit Material: Plastic Number of LED bulbs: 12 Working current: 100mA Input voltage: 4.8V?? 6.0V Light color: white, red, yellow, blue Connection mode: CH1 - servo CH2 - Speed controller CH3 - Receiver Applicable to: 1/10 RC vehicle LED cable length: about 300mm Circuit board size: 53 * 33 * 15mm Weight: 57.2g Lamp Description: Front light: 4 white LED lights Connect the lighting system to the CH3 on the receiver: The transmitter can independently control one set of lights, and when the vehicle accelerates, the other set of lights will light up; The receiver is not connected to CH3: one set of lights is always on, and the other set of lights is on when the car accelerates. Turn signal lamp: 4 yellow LED lamps When the remote control changes direction, the indicator lights will flash synchronously. Tail lights: 2 blue LED lights, 2 red LED lights The blue light is always on. When the car accelerates or brakes, the blue light goes out. Only when braking, the red light comes on. Installation method: CH2 transmitter: Connect the servo and ESC plugs to CH1 and CH2 on the lighting system, and then connect CH1 and CH2 to the receiver. CH3 transmitter: Connect the servo and ESC plugs to CH1 and CH2 on the lighting system, and then connect CH1, CH2, and CH3 to the receiver. Full simulation - steering - intelligent linkage of front and rear lights - full simulation when your car turns left or right - steering - intelligent linkage of front and rear lights - when your car turns left or right Turn signal (yellow) Follow left or right turn When your car brakes (red) Brake turn signal (yellow) Follow left or right turn When your car brakes (red) Brake The interface between the accelerator and the steering gear in the vehicle light system The interface between the accelerator and the steering gear in the vehicle light system The interface between the accelerator and the steering gear in the vehicle light system After a bit of integration, plug in the receiver and you can use it. After a bit of integration, plug in the receiver and you can use it Various channel control installation methods Various channel control installation methods Quantity: 12 LED lamps, including 3mm lamp caps for turn signal lamps and 5mm lamp caps for others Quantity: 12 lamps, including 3mm lamp caps for turn signal lamps and 5mm lamp caps for others The details are as follows Headlights: 4, white - 1. If connected to the third channel, the remote controller can control a group of headlights individually: 4, white - 1. If connected to the third channel, the remote controller can control a group of headlights individually The switch of the light, and the other group of lights are always on when accelerating; 2. If the third channel is not linked, the switch for one of the lights will keep the other group of lights on during acceleration; 2. If the third channel is not linked: one of them The group lights are always on, and the other group lights are always on during acceleration; The group lights are always on, and the other group lights are always on during acceleration; Turn signal: 4, yellow one flashing synchronously with the remote control changing left and right directions; Turn signal: 4, yellow one flashing synchronously with the remote control changing left and right directions; Tail lights: 4, of which 2 are always blue (blue lights will also go out when white headlights are lit) Tail lights: 4, of which 2 are always blue (blue lights will also go out when white headlights are lit) "When braking, it turns off, and the other two lights up when braking in red. Normally, it turns off.", It turns off when braking, and the other two lights up when braking in red. It turns off when braking normally Installation method: Installation method: 1. Remote control without a third channel (i.e. remote control). Modules without a control lamp set installed, such as Ledi 1. Remote control without a third channel (i.e. remote control). Modules without a control lamp set installed, such as Ledi FS-GT2B) Insert the plugs of the steering gear and electric regulator into CH1 and CH2 respectively, and then insert the linkage lamp FS-GT2B) Insert the plugs of the steering gear and electric regulator into CH1 and CH2 respectively, and then insert the linkage lamp The CH1 and CH2 on the group can be pled into the CH1 and CH2 channels on the receiver; The CH1 and CH2 on the group can be pled into the CH1 and CH2 channels on the receiver; 2. Remote control with a third channel (value remote control is equipped with a module to control the light group, such as the Ledi RC4G 2), remote control with a third channel (value remote control is equipped with a module to control the light group, such as the Ledi RC4G) Insert the plugs of the steering gear and the electric regulator into CH1 and CH2 respectively, and then insert the CHI on the linkage lamp set Plug the plugs of the steering gear and electric regulator into CH1 and CH2 respectively, and then connect the CHI on the linkage lamp set CH2 and Plug CH3 into channels CH1, CH2, and CH3 on the receiver. Plug CH3 into channels CH1, CH2, and CH3 on the receiver (Note: CH3 only needs to be pled into the receiver) (Note: CH3 only needs to be pled into the receiver)